Dimensions of strain are
  • A$ML{T^{ - 1}}$
  • B$M{L^2}{T^{ - 1}}$
  • C$ML{T^{ - 2}}$
  • D${M^0}{L^0}{T^0}$
Easy
art

Download our app
and get started for free

Experience the future of education. Simply download our apps or reach out to us for more information. Let's shape the future of learning together!No signup needed.*

Similar Questions

  • 1
    The least count of the main scale of a screw gauge is $1\, mm$. The minimum number of divisions on its circular scale required to measure $5\,\mu m$ diameter of a wire is
    View Solution
  • 2
    If the measurement errors in all the independent quantities are known, then it is possible to determine the error in any dependent quantity. This is done by the use of series expansion and truncating the expansion at the first power of the error. For example, consider the relation $z=x / y$. If the errors in $x, y$ and $z$ are $\Delta x, \Delta y$ and $\Delta z$, respectively, then

    $\mathrm{z} \pm \Delta \mathrm{z}=\frac{\mathrm{x} \pm \Delta \mathrm{x}}{\mathrm{y} \pm \Delta \mathrm{y}}=\frac{\mathrm{x}}{\mathrm{y}}\left(1 \pm \frac{\Delta \mathrm{x}}{\mathrm{x}}\right)\left(1 \pm \frac{\Delta \mathrm{y}}{\mathrm{y}}\right)^{-1} .$

    The series expansion for $\left(1 \pm \frac{\Delta y}{y}\right)^{-1}$, to first power in $\Delta y / y$, is $1 \mp(\Delta y / y)$. The relative errors in independent variables are always added. So the error in $\mathrm{z}$ will be $\Delta \mathrm{z}=\mathrm{z}\left(\frac{\Delta \mathrm{x}}{\mathrm{x}}+\frac{\Delta \mathrm{y}}{\mathrm{y}}\right)$.

    The above derivation makes the assumption that $\Delta x / x<<1, \Delta \mathrm{y} / \mathrm{y} \ll<1$. Therefore, the higher powers of these quantities are neglected.

    ($1$) Consider the ratio $\mathrm{r}=\frac{(1-\mathrm{a})}{(1+\mathrm{a})}$ to be determined by measuring a dimensionless quantity a.

    If the error in the measurement of $\mathrm{a}$ is $\Delta \mathrm{a}(\Delta \mathrm{a} / \mathrm{a} \ll<1)$, then what is the error $\Delta \mathrm{r}$ in

    $(A)$ $\frac{\Delta \mathrm{a}}{(1+\mathrm{a})^2}$ $(B)$ $\frac{2 \Delta \mathrm{a}}{(1+\mathrm{a})^2}$ $(C)$ $\frac{2 \Delta \mathrm{a}}{\left(1-\mathrm{a}^2\right)}$ $(D)$ $\frac{2 \mathrm{a} \Delta \mathrm{a}}{\left(1-\mathrm{a}^2\right)}$

    ($2$) In an experiment the initial number of radioactive nuclei is $3000$ . It is found that $1000 \pm$ $40$ nuclei decayed in the first $1.0 \mathrm{~s}$. For $|\mathrm{x}| \ll 1$, In $(1+\mathrm{x})=\mathrm{x}$ up to first power in $x$. The error $\Delta \lambda$, in the determination of the decay constant $\lambda$, in $\mathrm{s}^{-1}$, is

    $(A) 0.04$    $(B) 0.03$    $(C) 0.02$   $(D) 0.01$

    Give the answer quetion ($1$) and ($2$)

    View Solution
  • 3
    Match List $I$ with List $II$.

    LIST $-I$ LIST $-II$
    $(A)$ Torque $(I)$ $kg\,m ^{-1}\,s ^{-2}$
    $(B)$ Energy density $(II)$ $kg\,m\,s^{-1}$
    $(C)$ Pressure gradient $(III)$ $kg\,m ^{-2}\,s ^{-2}$
    $(D)$ Impulse $(IV)$ $kg\,m ^2\,s ^{-2}$

    Choose the correct answer from the options given below

    View Solution
  • 4
    The unit of length, velocity and force are doubled. Which of the following is the correct change in the other units?
    View Solution
  • 5
    If $L$ and $R$ are respectively the inductance and resistance, then the dimensions of $\frac{L}{R}$ will be
    View Solution
  • 6
    Two full turns of the circular scale of a screw gauge cover a distance of $1\ mm$ on its main scale. The total number of divisions on the circular scale is $50$. Further, it is found that the screw gauge has a zero error of $- 0.03\ mm$. While measuring the diameter of a thin wire, a student notes the main scale reading of $3\ mm$ and the number of circular scale divisions in line with the main scale as $35$. The diameter of the wire is  ....... $mm$
    View Solution
  • 7
    Dimensions of charge are
    View Solution
  • 8
    The acceleration due to gravity is measured on the surface of earth by using a simple pendulum. If $\alpha$ and $\beta$ are relative errors in the measurement of length and time period respectively, then percentage error in the measurement of acceleration due to gravity is
    View Solution
  • 9
    A Vernier calipers has $1 \mathrm{~mm}$ marks on the main scale. It has $20$ equal divisions on the Vernier scale which match with $16$ main scale divisions. For this Vernier calipers, the least count is
    View Solution
  • 10
    Diagrams show readings of a screw gauge. figure $(i)$ shows the zero error reading when the screw gauge is closed, figure $(ii)$ the reading when the screw gauge is being used to measure the diameter of a ball-bearing. What is the diameter of the ball-bearing in $mm$? There are $50$ divisions on circular scale
    View Solution